Min/Max
Step 第一步Basic 基础Coord.Effector 效果器Parameter 参数Deformer 分离器Falloff 女名女子名
Effector
效果器
强度[-∞ . . + ∞% ]
Use this setting to adjust the overall strength of the effect. Values of less than 0% and greater than 100% can be entered.
使用此设置来调整效果的整体强度。可以输入小于0% 和大于100% 的值。
选择
At left a Step Effector without a selection, at
right with a selection. 在左边的步骤效果没有选择，在右边的选择
A MoGraph Selection or MoGraph Weightmap tag can be dragged into this field or placed automatically by selecting a Cloner Object and an existing MoGraph selection/weighting, and creating an Effector.
MoGraph Selection 或 MoGraph Weightmap 标签可以拖放到这个字段中，或者通过选择 Cloner 对象和现有的 MoGraph 选择/权重并创建一个 Effector 自动放置。
The Effector will then work as follows, depending on the tag’s settings:
然后 Effector 将按照以下方式工作，具体取决于标记的设置:
Min/Max
最低/最高
最大[-∞ . . + ∞% ]
Use these settings to increase or decrease internal range values.
使用这些设置可以增加或减少内部范围值。
Note also the Remapping settings for the Layers in the Field list. Use this Field functionality as your preferred method since it’s more powerful and easier to understand in combination with other Layers.
还要注意字段列表中图层的重新映射设置。使用这个字段功能作为您的首选方法，因为它更强大，更容易理解与其他层组合。
最小[-∞ . . + ∞% ]
The values entered for the settings in the Parameter tab represent maximum values for those transformations. The Effector is free to choose from a range of values between 0% and this maximum value if the Minimum and Maximum sliders are set to 0% and 100%, respectively. Adjusting these sliders will affect the range of values from which the Effector has to choose accordingly.
为“参数”选项卡中的设置输入的值表示这些转换的最大值。如果最小和最大滑块分别设置为0% 和100% ，则效果器可以自由选择0% 和这个最大值之间的范围。调整这些滑块将影响效果器必须相应选择的值范围。
Example: 例子:R.P is set to 90° in the Parameter tab. The following will apply:
在“参数”选项卡中将 R.P 设置为90 ° 。以下内容将适用:
Minimum = 0%; Maximum = 100%: The first clone will be located at 0°, the last at 90°.
最小 = 0% ; 最大 = 100% : 第一个克隆位于0 ° ，最后一个克隆位于90 ° 。
Minimum = -100%; Maximum = 100%: The first clone will be located at -90%, the last at +90%.
最小 =-100% ; 最大 = 100% : 第一个克隆位于 -90% ，最后一个克隆位于 + 90% 。
花键
The transformation shown is a result of the spline
setting (insert) and a 所显示的转换是样条设置(插入)和S.Y 女名女子名 setting of 10. 设定为10
Use these function graphs (see also Function Graphs) to influence the interpolation between the first and last clone. The interpolation will take place as it is shown by the graph.
使用这些函数图(参见函数图)来影响第一个和最后一个克隆之间的插值。插值将如图所示进行。
步距[0. . 2147483647]
Step Gap 步距 settings from
left to right: 0,2,10. 从左到右设置: 0,2,10
Use this setting to influence the interpolation values between the beginning clone and end clone. Increasing values greater than 0 will result in a lessening of the difference between each clone; differences between clone groups, within which no transformations take place, will still be evident.
使用此设置可以影响开始克隆和结束克隆之间的插值值。增加大于0的值将减少每个克隆之间的差异; 克隆群组之间的差异仍然很明显，在这些差异中没有发生转换。