Geometry Clone 几何克隆Basic 基础Inputs 投入Outputs 产出
Inputs
投入
几何学
Here you can pass the geometry to the Node whose points or polygons you want to clone.
在这里，您可以将几何图形传递给要克隆其点或多边形的 Node。
模式
Here you can select from Polygons or Points to be cloned.
在这里你可以选择多边形或点要克隆。
选择
polygon selection will be evaluated automatically.
多边形选择将被自动评估。
克隆〔0.2147483647〕
Here you can enter the number of clones. This count does not include the output element.
在这里您可以输入克隆的数量。这个计数不包括输出元素。
偏移量[-∞ . . + ∞ m ]
This value defines the distance from the initial element to the last clone along the selected shape axis. All intermediate clones will simultaneously be distributed along the same distance.
该值定义了从初始元素到最后一个克隆沿所选形状轴的距离。所有中间无性系将同时沿同一距离分布。
漏洞[0. . 100% ]
This percentage value defines how many cloned elements should be output. For the winding staircase, several steps would be missing. If set to 0%, the complete number of clones will be generated. If set to 50%, only half of them will be generated. The omitted elements will be selected randomly. If 100% is defined, no new elements will be generated.
这个百分比值定义了应该输出多少克隆元素。对于旋转楼梯来说，有几个台阶是缺失的。如果设置为0% ，将生成完整的克隆数。如果设置为50% ，则只能生成一半。省略的元素将被随机选择。如果定义了100% ，则不会生成新元素。
比例[0. . 100% ]
This value defines the size that the last clone should have. If set to 50%, for example, the last clone will be half as large as the initial element. If set to 100%, the size will remain unchanged.
这个值定义了最后一个克隆应该具有的大小。例如，如果设置为50% ，那么最后一个克隆将只有初始元素的一半大。如果设置为100% ，大小将保持不变。
轴心
This value defines the geometry axis around which the clones will rotate. For a winding staircase, this would be the cube’s Y axis. For a realistic-looking winding staircase, the axis should lie slightly outside of the cube.
此值定义克隆将围绕其旋转的几何轴。对于旋转楼梯，这是立方体的 y 轴。对于一个看起来很真实的旋转楼梯，轴应该稍微位于立方体的外部。
Rotation[-5729577951308232523776..5729577951308232523776°]
轮流[-5729577951308232523776.5729577951308232523776 ° ]
This value defines the distance to which the clones should rotate around the geometry axis. If set to 180°, half a rotation will be generated, if set to 360° a complete rotation will be generated.
此值定义克隆围绕几何轴旋转的距离。如果设置为180 ° ，将产生半个旋转，如果设置为360 ° ，将产生一个完整的旋转。
移动变量[ XYZ m ]
All clones will be assigned a fixed position. This position can be varied using the Move Var. setting. If, for example, the Y position has a value of 10, the clones can vary between -10 and 10 in their Y position.
所有克隆将被指定一个固定的位置。这个位置可以使用移动变量来改变。设置。例如，如果 y 位置的值为10，那么克隆在其 y 位置上可以在 -10和10之间变化。
比例变量[% ]
These values can be used to vary the clones’ size. The values are percentage values.
这些值可以用来改变克隆的大小。这些值是百分比值。
If set to 100%, the clones’ size will remain unchanged. If, for example, the X value is set to 50%, the X size of individual elements can vary between 50% and 100%; if set to 0%, the size will vary between 0% and 100%; if set to 200%, the size will vary between 100% and 200%.
如果设置为100% ，克隆的大小将保持不变。例如，如果 x 值设置为50% ，单个元素的 x 大小可以在50% 到100% 之间变化; 如果设置为0% ，大小将在0% 到100% 之间变化; 如果设置为200% ，大小将在100% 到200% 之间变化。
Example: X = 200%, Y = 100%, Z = 50%. This produces a ratio of 2:1, 1:0.5. The clones’ sides can only be scaled in this ratio. If this option is disabled, the clones’ sides can be scaled independently of one another.
例如: x = 200% ，y = 100% ，z = 50% 。这样得到的比率是2:1,1:0.5。克隆体的侧面只能按这个比例缩放。如果此选项被禁用，克隆的侧面可以相互独立地进行缩放。
旋转变量[ HPB ° ]
Each clone will be assigned its own virtual axis (this will be calculated based on the clone’s center of gravity). The clones can be rotated randomly. The degree that can be defined for each rotation axis defines the maximum positive and negagtive rotation around the respective axis.
每个克隆将被分配它自己的虚拟轴(这将根据克隆的重心计算)。克隆体可以随机旋转。可以为每个旋转轴定义的度定义了围绕各自轴的最大正负旋转。
An angle of 45° would restrict the clones to a rotation between -45° and 45°.
角度为45 ° 时，无性系的旋转角度限制在 -45 ° 和45 ° 之间。
统一比例尺
If this option is enabled, the percentage values defined for X, Y and Z will also serve as ratio.
如果启用此选项，为 x、 y 和 z 定义的百分比值也将作为 ratio。