Anisotropy

各向异性

Active

活跃

Projection

投影

The type of projection is used to define the anamorphic (disproportional) scaling of the specular highlights. It can also define the scratch direction to be used with the reflection and environment convolution groups. The projections are transformed by the Material tag used to apply them to an object.

投影类型用于定义镜面高光的变形(非比例)缩放。它还可以定义与反射和环境体积积组一起使用的划痕方向。这些投影通过材质标签进行转换，用于将它们应用到一个物体上。

Planar

平面

A flat XY planar projection.

平面 XY 投影。

Auto Planar

自动平面

Automatically projects on a plane parallel to the current normal.

自动投影在与当前法线平行的平面上。

Shrink Wrap

收缩包装

A spherical projection for scaling direction, but uses a separate algorithm for projecting the scratches.

一个球面投影用于缩放方向，但使用一个单独的算法投影划痕。

Radial Auto Planar

径向自动平面

Automatically projects on a plane parallel to the current normal.

自动投影在与当前法线平行的平面上。

Radial Pattern Auto Planar

径向图自动平面

Creates a multi-origin radial scratch pattern that is parallel to the current normal.

创建一个多源径向划痕模式是平行于当前正常。

Radial Planar
Radial Pattern Planar

径向平面/径向图案平面

Projection Scale[0..1000%]

推算比例[0. . 1000% ]

Scales the scratch algorithms that have an actual pattern (Radial Pattern is the only current algorithm of this type to which scale applies).

缩放具有实际模式的划痕算法(径向模式是目前唯一适用于缩放的此类算法)。

X Roughness[0..+∞%]

X 粗糙度[0. . + ∞% ]

Scale the highlights in the X direction defined by the Scratch Projection algorithm. The appropriate range is 0.1% to 10,000%. If the X & Y roughness are the same, the standard internal specular algorithm is used.

缩放由 Scratch Projection 算法定义的 x 方向上的高光。适当的范围是0.1% 至10,000% 。如果 x 和 y 的粗糙度相同，则使用标准的内镜算法。

Y Roughness[0..+∞%]

Y 粗糙度[0. . + ∞% ]

Scale the highlights in the Y direction defined by the Scratch Projection algorithm. The appropriate range is 0.1% to 10,000%. If the X & Y roughness are the same, the standard internal specular algorithm is used.

按抓取投影算法定义的 y 方向缩放高光。适当的范围是0.1% 至10,000% 。如果 x 和 y 的粗糙度相同，则使用标准的内镜算法。

Specular 1
Specular 2
Specular 3

镜面1镜面2镜面3

Use these check boxes to define which Specular channels should be affectec by anistropic scratches. Note that 3 more options of the same name are located farther below. This is where you define whether or not the scratch texture should be included in the calculation of the specular light.

使用这些复选框来定义哪些 Specular 通道应该受到阴影划痕的影响。请注意，下面还有3个同名的选项。这是您定义是否应该包括在计算镜面光的刮痕纹理。

Amplitude[0..100%]

幅度[0. . 100% ]

Scales the effect of the scratch of the specular highlights. The higher the value, the more scratched the speculars will look. The appropriate range is 0% - 100%.

缩放镜面高光部分划痕的效果。值越高，投资者看到的投机行为就越多。适当的范围是0%-100% 。

Scale[0..+∞%]

比例[0. . + ∞% ]

Scales the scratch pattern itself. This applies to all scratch algorithms.

缩放划痕模式本身。这适用于所有划痕算法。

Length[0..+∞%]

长度[0. . + ∞% ]

Defines the scratch length in the space of the scratch pattern. Smoother milled surfaces would use a higher scratch length and rougher surfaces would use smaller values. The appropriate range is 1% - 1,000%.

定义划痕模式空间中的划痕长度。光滑表面将使用更高的划痕长度和粗糙的表面将使用更小的价值。适当的范围是1%-1,000% 。

Attenuation[0..+∞%]

衰减[0. . + ∞% ]

Scales the amount of detail of the scratches based upon the samples, angle to the camera and the distance from the camera. The larger the values, the greater the attenuation, causing less scratching (better for animation); the smaller the value, the greater the detail (better for still images). The appropriate range is 0% - 1000%.

根据样品、相机的角度以及与相机的距离来衡量划痕的细节。值越大，衰减越大，导致擦伤越小(对动画效果更好) ; 值越小，细节越大(对静态图像效果更好)。适当的范围是0%-1000% 。

Specular 1
Specular 2
Specular 3

镜面1镜面2镜面3

These check boxes specify which specular channels will be affected by the anisotropic scratches (i.e., the scratch texture; see also the description of the same name above).

这些复选框指定哪些镜面通道将受到各向异性划痕(即划痕纹理; 请参阅上面同名的描述)的影响。