Options

选择

Maximum Angle[0..180°]

最大角度[0. . 180 ° ]

If Preserve Groups is enabled, polygons not exceeding this angle to each other will stay together during the extrude inner. If the polygons exceed this angle, they will be broken apart.

如果启用 Preserve Groups，相互间角度不超过这个角度的多边形将在挤压内部时保持在一起。如果多边形超过这个角度，它们就会被分开。

Offset[-∞..+∞m]

偏移量[-∞ . . + ∞ m ]

Defines the width of the inner extrusion (that is, the distance between an edge of the original polygons and the corresponding edge of the inner extrusion).

定义内挤压的宽度(即原始多边形的边缘和相应的内挤压边缘之间的距离)。

Offset Variation[0..+∞%]

偏移量变化[0. . + ∞% ]

Gives a percentage value for the variation of the width of Extrude Inner. This option is only available if Preserve Groups is disabled.

给出挤压内部宽度变化的百分比值。此选项仅在禁用 Preserve Groups 时可用。

0% - No deviation from the selected Offset value.

0%-与选定的偏移量值无偏差。

60% - All selected polygons are inward extruded between 40% and 100% of the Offset value.

60%-所有选定的多边形都向内挤压到胶印值的40% 到100% 之间。

100% - All selected polygons are inward extruded between 0% and 100% of the Offset value.

100%-所有选定的多边形都向内挤压到胶印值的0% 到100% 之间。

180% - All selected polygons are extruded between -80% (outward) and 100% (inward) of the Offset value.

180%-所有选定的多边形被挤压在偏移量值的 -80% (向外)和100% (向内)之间。

Var 0% and 60%. 0% 和60%

Subdivision[1..+∞]

细分[1. . + ∞]

Here you can define the number of subdivisions for the inner extrude.

这里您可以定义内部挤压的细分数。

Subdivision set to 0 and 2. 细分设置为0和2

Create N-gons

创建 n 个图形

Enable this option if you have defined subdivisions but want to avoid the additional edges between the original polygons and the inner extrude that this would normally cause.

如果您已经定义了细分，但是希望避免原始多边形和内部挤压之间的附加边缘，则启用此选项。

Preserve Groups

保护群体

If this option is enabled, the connected polygons will stay together during extrusion, provided they do not exceed the Maximum Angle relative to each other.

如果启用此选项，连接的多边形将在挤压期间呆在一起，只要它们不超过相对于彼此的最大角度。

Preserve Groups enabled and disabled. 保留启用和禁用的组 Proceed with caution when inner extruding several connected polygons that you want to keep as a group. In the following example, only the outer edges of the selection are moved inwards. The edges of the inner surfaces of the selection are not affected. 继续小心当内部挤压几个连接的多边形，你想保持作为一个组。在下面的示例中，只将选定内容的外边缘向内移动。所选内表面的边缘不受影响

Before and after extruding inwards - only the outside edges will be moved. 在向内挤压之前和之后-只有外边缘会被移动

This can lead to problems when starting with a certain Offset value, since the outer edges can possibly overlap with the internal ones. The problem occurs when starting with an Offset value that is set too high.

当以某个偏移量值开始时，这可能会导致问题，因为外边缘可能与内边缘重叠。如果偏移量值设置得太高，就会出现问题。

Offset set too high. 偏移量设置得太高

To remedy, set Offset to a lower value.

若要补救，请将“偏移量”设置为较低的值。