Clone 克隆Options 选择Tool 工具
Options
选择
克隆〔1.1000〕
Defines the number of clones along the selected object axis. Offset, Scale and Rotation specify the parameters for the final clone. The intermediate clones use interpolated values.
定义沿所选对象轴的克隆数。偏移量、缩放和旋转指定最终克隆的参数。中间克隆使用插值值。
偏移量[-∞ . . + ∞ m ]
Gives the distance from the start element to the last clone along the selected object axis. All intermediate clones are distributed evenly over this distance.
给出从起始元素到沿所选对象轴的最后一个克隆的距离。所有中间克隆均匀地分布在这个距离上。
漏洞[0. . 100% ]
With this percentage value you can define the number of cloned elements that you want to be omitted from the total. With 0% the full number of clones is created. With 50% only half will be created. The omitted elements are randomly selected. With 100% no new elements at all will be created.
使用这个百分比值，可以定义希望从总数中省略的克隆元素的数量。如果是0% ，则创建完整的克隆数量。只有50% 会被创造出来。省略的元素是随机选择的。100% 不会创建任何新元素。
比例[0. . 100% ]
This parameter enables you to scale the clones. The scale of the clones will increase gradually all the way to the last clone. Enter the size of the final clone as a percentage of the start element’s size. For example, if you enter a vaue of 50%, the last clone will be half as large as the initial clone. A value of 100% will not modify the size of subsequent clones.
此参数允许您缩放克隆。克隆的规模将逐渐增加，一直到最后一个克隆。输入最终克隆的大小占开始元素大小的百分比。例如，如果输入一个50% 的区域，最后一个克隆将是最初克隆的一半大。100% 的值不会修改后续克隆的大小。
轴心
Defines the object axis about which the clones are to be rotated. For example, to create a spiral staircase, set Axis to Y.
定义要旋转克隆的对象轴。例如，要创建螺旋楼梯，请将轴设置为 y。
旋转[-∞ . . + ∞ ° ]
Defines the angle through which the clones are rotated. With 180° the object would rotate half a revolution from start to finish; with 360° a full rotation is made.
定义克隆旋转的角度。180 ° 时，物体会自始至终旋转半公转; 360 ° 时，物体会完全旋转。
移动变量[ XYZ m ]
By default, all clones are assigned a fixed position that depends on the above settings. You may vary these positions using Move Variation. For example, if you set the Move Variation value for Y to 10, each clone can deviate from -10 to 10 units in their Y position.
默认情况下，所有克隆被分配一个固定的位置，这取决于上面的设置。您可以使用移动变化改变这些位置。例如，如果将移动变异值设置为10，每个克隆体的 y 位置可以偏离 -10到10个单位。
比例变量[% ]
Defines the variation in the size of the clones as a percentage.
以百分比形式定义克隆大小的变化。
At 100% the size is not varied. Entering 50% for the X value means that the X size of the individual elements can vary between 50% and 100%.
在100% 的情况下，大小没有变化。为 x 值输入50% 意味着单个元素的 x 大小可以在50% 到100% 之间变化。
With 0% the size varies between 0% and 100%. If you enter 200% then the value will vary between 100% and 200%.
如果是0% ，大小在0% 到100% 之间变化。如果输入200% ，那么该值将在100% 到200% 之间变化。
腐烂。变种。[ HPB ° ]
Each element is assigned its own virtual axis. The element may then be rotated randomly around its axis with the value entered here. The value, in degrees, that you enter for each rotation axis defines the maximum positive and negative rotation about the appropriate axis. 45° would indicate that the clones can vary in their radial rotation from -45° to 45° at each clone.
每个元素都有自己的虚拟轴。然后，可以随机地将元素绕其轴旋转，并在此处输入值。您为每个旋转轴输入的度数定义了围绕相应轴的最大正向和负向旋转。45 ° 表明，每个克隆的径向旋转角度在 -45 ° 到45 ° 之间变化。
统一比例尺
If this option is enabled, the percentages entered for X, Y and Z are used for relative scaling. For example, with Uniform Scale enabled, X set to 200%, Y to 100% and Z to 50%, the ratio of scaling is 2:1:0.5; the individual elements can then be scaled only according to this ratio. If this option is disabled, the axes of the individual elements can be varied in scale independently.
如果启用此选项，则为 x、 y 和 z 输入的百分比将用于相对缩放。例如，启用 Uniform Scale，x 设置为200% ，y 设置为100% ，z 设置为50% ，缩放比例为2:1:0.5; 然后单个元素只能根据这个比例进行缩放。如果禁用此选项，则单个元素的轴可以独立地按比例变化。