Array 数组Options 选择Tool 工具
Options
选择
Clones X[1..1000]
Y[1..1000]
Z[1..1000]
克隆 x [1.1000] y [1.1000] z [1.1000]
Defines the number of clones along each object axis.
定义沿每个对象轴的克隆数。
This value also includes the original element. For example, if you enter the value of 2 for all three axes, it results in a total number of 2x2x2=8. In effect, however, only 7 actual clones are produced.
此值还包括原始元素。例如，如果您为所有三个轴输入值2，那么结果总共是2x2x2 = 8。然而实际上，只有7个真正的克隆产生了。
偏移量[ XYZ m ]
Defines the size of the array. You can enter different values for each of the X, Y and Z directions. These values are absolute — they refer to the entire size of the array (including the start element).
定义数组的大小。您可以为每个 x、 y 和 z 方向输入不同的值。这些值是绝对值ー它们指的是数组的整个大小(包括起始元素)。
漏洞[0. . 100% ]
This value adds a random factor to the number of elements that are created. You may enter values from 0% to 100%.
此值向创建的元素数添加一个随机因子。您可以输入从0% 到100% 的值。
A value of 0% means the complete number of elements that has been input is created. With 50% only half of the elements are created — which elements are omitted is selected randomly. With 100% no new elements will be created.
值为0% 表示创建了已经输入的完整元素数。只创建了50% 的元素ーー省略的元素是随机选择的。100% 不会创建新元素。
移动变量[ XYZ m ]
These parameters define how the positions of the duplicated elements vary. This arrangement enables you to assign either accurate or uneven positioning.
这些参数定义了重复元素的位置如何变化。这种安排使您可以分配准确或不均匀的定位。
If the values for all axes are set to 0 then an accurate position is assigned to each duplicated element. If you set the X value to 100, however, the individual elements can deviate from -100 to +100 units from their position in the X direction.
如果所有轴的值都设置为0，那么将为每个重复的元素指定一个精确的位置。但是，如果将 x 值设置为100，那么单个元素可以偏离 x 方向上的位置，从 -100到 + 100个单位不等。
比例变量[% ]
Defines the variation of the element size. The values are shown as a percentage.
定义元素大小的变化。值以百分比显示。
100% means that the size is not affected. For example, entering 50% for the X value results in the X size of the individual elements varying from 50% to 100%. With 0% the size varies from 0% to 100%.
100% 意味着大小不受影响。例如，为 x 值输入50% 会导致单个元素的 x 大小在50% 到100% 之间变化。在0% 的情况下，尺寸从0% 到100% 不等。
腐烂。变种。[ HPB ° ]
Each element is assigned its own virtual axis. The elements may then be rotated randomly. The values, in degrees, which you enter for each rotation axis define the maximum positive and negative rotation around the appropriate axis. 45° would mean that the element can rotate in a radial zone from -45° to 45° in each case.
每个元素都有自己的虚拟轴。然后元素可以随机旋转。您为每个旋转轴输入的度数值定义了围绕相应轴的最大正负旋转。45 ° 意味着在每种情况下，元件可以在径向区域内从 -45 ° 转到45 ° 。
统一比例尺
Both marked cubes were varied using a disabled
两个标记的立方体使用禁用的变化Uniform Scale 统一比例尺 option on the left and an activated 选项在左边和一个激活Scale
Var. 变量标度 option on the right, each set to 选项在右边，每一组10%.
If this option is enabled, the percentage values chosen for X, Y and Z will also be used for relative scaling. For example: Scale Var. X = 200%, Y = 100%, Z = 50% results in a relation of 2:1:0.5. The individual elements can then be scaled only according to this relative scaling. If this option is disabled, the axes of the individual elements can be scaled independently.
如果启用此选项，则为 x、 y 和 z 选择的百分比值也将用于相对缩放。例如: Scale Var。X = 200% ，y = 100% ，z = 50% 的结果是2:1:0.5。然后，单个元素只能根据这种相对缩放进行缩放。如果禁用此选项，则可以独立缩放各个元素的轴。